Jordans mod menu v1.0 update#
Jordans mod menu v1.0 archive#
Jordans mod menu v1.0 Pc#

If you don`t know what a trinket is, its a cheap SAMD microcontroller with USB host mode.ĭouble press RESET button to get into downloader mode and drag and drop contents of the archive you choose from below. Or Hekate 2.3 depending on which binary you flash. If you have a trinket M0, then flash this in bootloader mode and it will give you the SX loader on the device. Credits to all in that thread who have been involved in the Trinket M0. I`ve added Dotstar support and different payloads. This was in the dongle development thread. It is just an Ardudildo sketch with the loader payload added.

The possibility of killing your switch through bad soldering is huge.Įvening ladies and gents. It isn`t for the feint of heart but it works.

You either need to drill a hole in the back of the switch casing and shield, or it is possible to attach it to the metal shielding on the back and you can just press the back cover to activate the switch as its a tight fit.

The pain in the arse comes when you want to update the payload on the trinket. Its just one of them 'get round to it' jobs. I said I`d do a write-up how I`d done mine. So you need to fit it to another point on board with the other bits that only let it run for 3 or 4 seconds. Or it will run your battery down eventually. So you need a little addition to the trinket (a couple of components) which only let the trinket run for 3 or 4 seconds as power button pressed. If you rip this pad, you WILL NEED TO REMOVE YOUR BOARD and run from a testpoint.Ĭonnect to 4v feed from battery, connect to testpoints behind USB port. If you aren`t the best at soldering, then think very carefully about connecting to pin 6 capacitor (the one in these new methods). Take a look at alternative solder points to get you out of the sh*t if you do rip something off the board Use a cocktail stick for more glue control!!! Put the tiniest amount of glue on the PCB mask only.

Only use glue if you need to and glue wires after soldering. Good soldering iron needed - ideally with a 0.3 conical tip. IF YOU ARE STRUGGLING, OR THINK YOU ARE GOING TO STRUGGLE, PLEASE PLEASE SOLDER TO THE TEST POINTS NOTED IN THIS AND OTHER THREADS (YOU WILL NEED TO REMOVE THE MOTHERBOARD). WE ARE SOLDERING TO TRACES AND COMPONENTS ON THE FRONT SIDE OF THE BOARD TO SAVE HAVING TO REMOVE THE BOARD AND SOLDER TO TESTPOINTS. Leave for 15 minutes and switch will start normally. Search for Fusee Suite or go to link at top of this OP.Ī - Have you got the charger connected? Disconnect it or your switch won't boot! Boot to a payload (SX loader/Hekate), reconnect charger and leave on the payload menu and charge. You are just causing yourself more headaches. Looks nice, good resistance to elements, tidy. I recommend Kynar wrapping wire but any will do. And if you snap it, chances are the wire will snap and not the trace / component.Ī2 - You can also use AWG30. CHECK YOUR GLUE WON`T GO CONDUCTIVE OVER TIME - LOOKING AT YOU SCAMSUNG! The combination of heat cycles and absorbing of moisture can turn adhesive into a high-impedance connection!Ī - I use AWG40 magnet wire or AWG30 Kynar. Acetone tends to remove / melt anything to be warned. Epoxy won`t stick to the shield long-term, so bear that in mind. The only thing super about it is how it melts things. Superglue makes a mess DO NOT USE SUPERGLUE. You are in RCM.Ī - Only glue if necessary! Ideally if your soldering is of sufficient quality and your wire is thin enough, you don`t need glue.

Plug into your PC and it should recognise a APX device. Once shorted out, hold down vol+ and power. Q - How do I boot the switch into APX (RCM) mode?Ī - You need to short out pin 10 on the right joycon rail to GND with a jig or modded joycon or paperclip (not recommended.

Jordans mod menu v1.0 update#

Jordans mod menu v1.0 Pc#